思科7200路由器MultiChannel怎么配置
权威分享
思科用自己敏锐的洞察力、丰富的行业经验、先进的技术，帮助企业把网络应用转化为战略性的资产，充分挖掘网络的能量，获得竞争的优势，那你知道思科7200路由器MultiChannel怎么配置吗?下面是学习啦小编整理的一些关于思科7200路由器MultiChannel怎么配置的相关资料，供你参考。
思科7200路由器MultiChannel配置的过程：
1.Controller Configuration Examples控制器配置举例
The following example shows a typical controller configuration for
the multichannel E1/PRI port adapter on a Cisco 7200 series or
Cisco uBR7200series router:
router> enable router# configure terminal router(config)# controller E1 1/0 router(config-controller)# framing crc4 router(config-controller)# linecode hdb3 router(config-controller)# clocksource internal router(config-controller)# channel-group 0 timeslots 1-31 router(config-controller)# description ppp channel 5 router(config-controller)# shutdown router(config-controller)# ^Z |
2.Interface Configuration Examples接口配置举例
The following example shows a typical interface configuration for
the multichannel E1/PRI port adapter on a Cisco 7200 series or
Cisco uBR7200 series router:
router> enable router# configure terminal router(config)# interface serial router(config)# interface serial 4/1:0 router(config-if)# encapsulation ppp router(config-if)# description ppp channel 5 router(config-if)# no shutdown router(config-if)# ^Z |
3. Configuring Multichannel E1 Interfaces 配制多通道E1接口
The channel groups must be mapped before the multichannel E1/PRI
controller can be configured. The following are controller commands
used to map the channel group (the default variable is listed first):
controller E1 port-adapter-slot number/port-number (for Cisco 7200
series router)
clock source [line | internal]
linecode [ami | hdb3]
framing [crc4 | no-crc4]
loopback [diagnostic | local {payload | line}]
shutdown
channel-group number timeslots list
Number is the channel group 0 to 30.
list is a number between 1 and 31. You can enter timeslots individually
and separate them by commas, or enter them as a range separated by
a hyphen (for example, 1-3, 8, 9-18). Timeslot 0 is an illegal
configuration. |
4.常用调试命令
show version or show hardware Displays system hardware configuration, the number of each interface type installed, Cisco IOS software version, names and sources of configuration files, and boot images show controllers Displays all the current interface processors and their interfaces show diag slot Displays types of port adapters installed in your system and information about a specific port adapter slot, interface processor slot, or chassis slot show interfaces type 0 or 1/ interface-port-number Displays status information about a specific type of interface (for example, serial) on a Catalyst RSM/VIP2 show interfaces type mod_num/bay/port Displays status information about a specific type of interface (for example, serial) on a Catalyst 6000 family FlexWAN module show interfaces type 3/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco 7120 series router show interfaces type 4/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco 7140 series router show interfaces type port-adapter-slot-number/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco 7200 series router show interfaces type 1/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco uBR7223 router show interfaces type 1 or 2/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco uBR7246 router show interfaces type interface-processor-slot-number/port-adapter- slot-number/interface-port-number Displays status information about a specific type of interface (for example, serial) on a VIP2 or VIP4 in a Cisco 7000 series or Cisco 7500 series router Router# show interfaces serial 3/1/0 show protocols Displays protocols configured for the entire system and for specific interfaces show running-config Displays the running configuration file show startup-config Displays the configuration stored in NVRAM |
5. show Cisco 7200 Series and Cisco uBR7200 Series Routers
下列显示72的SHOW结果!
Following is an example of the show interfaces serial port-adapter- slot-number/port-number:channel-group command for Cisco 7200 series and Cisco uBR7200 series routers. It shows all of the information specific to the first multichannel E1/PRI port (port 0) in port adapter slot 2, channel group 1: Router# show interfaces serial 2/0:1 Serial2/0:1 is up, line protocol is up (looped) Hardware is Multichannel E1 Internet address is 1.6.0.1/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) Last input 00:00:07, output 00:00:07, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0 (size/max/drops); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/64/0 (size/threshold/drops) Conversations 0/1 (active/max active) Reserved Conversations 0/0 (allocated/max allocated) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 87 packets input, 6521 bytes, 0 no buffer Received 87 broadcasts, 0 runts, 0 giants 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 87 packets output, 6521 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 1 carrier transitions no alarm present Timeslot(s) Used:1-31, subrate: 64Kb/s, transmit delay is 0 flags |
看过文章“思科7200路由器MultiChannel怎么配置”的人还看了：
6.cisco怎么样
10.思科路由器如何启动
